The production of the CV boards and the front panels for CV Adder should
start next week as there were no additional suggestions since the
announcement of the module in May 2007 and the polls for this module in June
2007. But I'll try to stop the production of the pc boards and front panels.

How about this simple solution: A default voltage of +1.00V is connected to
the switching contacts of the input socktes #1 and #2. This would add these
features:

As long as no cable is connected to input #1 it works as a manually
adjustable offset with up to +/- one octave.
As long as no cable is connected to input #2 it works as an octave switch
(+/- one octave).

With this solution one can decide if the inputs #1 and #2 can be used as
offset control and octave switch or as originally planned.

Best wishes
Dieter Doepfer

> -----Ursprungliche Nachricht-----
> Von: Doepfer_a100@yahoogroups.com
> [mailto: Doepfer_a100@yahoogroups.com ]Im Auftrag von Denis Gokdag
> Gesendet: Donnerstag, 9. August 2007 15:38
> An: Doepfer_a100@yahoogroups.com
> Betreff: Re: 1 Re: A-185-2 Precision CV Adder last minute
> comment
>
>
> *grin*
>
> The octave switch is a good idea.
>
> Cheers,
> Denis
>
> On 09. Aug 2007, at 3:06 PM, Silas Johansen wrote:
>
> > Good idea - I wouldn't like to have to use a voltage inverter to
> > reinvert an
> > inverted voltage just to get an uninverted voltage. Much better to
> > save my
> > inverter for inverting uninverted voltages in order to get inverted
> > ones.
> > Also, when doing too many inversions you might inadvertently invert
> > too few
> > or too many times, which may, in conclusion, cause confusion.
> >
> > :-P
> >
> > Silas
> >
> > On 8/9/07, gabu_004 < gabu_004@... > wrote:
> > >
> > > Yes that's a very good idea... this should be taken into
> > > consideration!
> > >
> > > g.
> > >
> > >
> > > --- In Doepfer_a100@yahoogroups.com <Doepfer_a100%
> > 40yahoogroups.com>,
> > > "jalmari3" <jari.jokinen@...>
> > > wrote:
> > > >
> > > > No one agrees
> > > >
> > > > --- In Doepfer_a100@yahoogroups.com <Doepfer_a100%
> > 40yahoogroups.com>,
> > > "jalmari3" <jari.jokinen@>
> > > > wrote:
> > > > >
> > > > > I can't figure the Yahoo mess, so I start a new topic. Sorry.
> > > > >
> > > > >
> > > > > It is propably too late, but:
> > > > >
> > > > > - Adding octave switch and/or offset knob to the A-185-2 could
> > > make
> > > > it
> > > > > a one stop pitch control center. My controllers and oscillators
> > > > don't
> > > > > have octave switches...
> > > > >
> > > > > - I might prefer 3 non-inverted outputs and 1 inverted output
> > > > instead
> > > > > of 2 non-inverted outputs and 2 inverted outputs.
> > > > >
> > > > >
> > > > > Best regards
> > > > > Jari Jokinen
> > > > >
> > > >
> > >
> > >
> > >
> >
> > [Non-text portions of this message have been removed]
> >
> >
> >
>
> [Non-text portions of this message have been removed]
>
>
>