yes, analogue solutions modules use the same connector. red stripe goes to -12volts in the doepfer busboard.
Bakis Sirros - Parallel Worlds / Interconnected / Memory Geist
1 group owner
www. parallel - worlds - music. com
www. myspace. com/ parallelworldsmusic
www. myspace. com/ interconnectedmusic
www. myspace. com/ memorygeist
www. DiN. org. uk
www. musicamaximamagnetica. com
www. vu-us. com
www. shimarecords. co. uk
--- On Tue, 2/23/10, Steve <
stevebdar@...
> wrote:
From: Steve <
stevebdar@...
>
Subject: Re: 1 Newbie Question: Adding a Plan B M17 to a Doepfer 9U Case
To:
Doepfer_a100@yahoogroups.com
Date: Tuesday, February 23, 2010, 12:08 AM
Ok Thanks...I will get some adapters.
I also have a Analogue Solutions SQ8. The ribbon and connector look the same as the doepfers I am putting in. Can that work in the case
Cheers,
Steve B
--- On Mon, 2/22/10, Bakis Sirros <synth_freak_ 2000@yahoo. com> wrote:
From: Bakis Sirros <synth_freak_ 2000@yahoo. com>
Subject: Re: 1 Newbie Question: Adding a Plan B M17 to a Doepfer 9U Case
To: Doepfer_a100@ yahoogroups. com
Date: Monday, February 22, 2010, 2:41 PM
hi Steve,
no.
Analogue systems modules have different connectors!
you can buy special connectors to connect ASystems modules to a doepfer case from analogue systems (or analogue haven, i think):
thanks,
Bakis.
Bakis Sirros - Parallel Worlds / Interconnected / Memory Geist
1 group owner
www. parallel - worlds - music. com
www. myspace. com/ parallelworldsmusic
www. myspace. com/ interconnectedmusic
www. myspace. com/ memorygeist
www. DiN. org. uk
www. musicamaximamagneti ca. com
www. vu-us. com
www. shimarecords. co. uk
--- On Mon, 2/22/10, Steve <stevebdar@yahoo. com> wrote:
From: Steve <stevebdar@yahoo. com>
Subject: Re: 1 Newbie Question: Adding a Plan B M17 to a Doepfer 9U Case
To: Doepfer_a100@ yahoogroups. com
Date: Monday, February 22, 2010, 10:31 PM
Hi Bakis:
Would the same apply to an ASys RS50 and RS60
Thanks
Steve B
--- On Sat, 2/13/10, Bakis Sirros <synth_freak_ 2000@yahoo. com> wrote:
From: Bakis Sirros <synth_freak_ 2000@yahoo. com>
Subject: Re: 1 Newbie Question: Adding a Plan B M17 to a Doepfer 9U Case
To: Doepfer_a100@ yahoogroups. com
Date: Saturday, February 13, 2010, 2:57 AM
hi Steve,
Plan B modules use the standard doepfer type ribbon power cable.
just make sure that the red stripe goes to -12volts on both the busboard and on the module PCB ends.
thanks,
Bakis.
Bakis Sirros - Parallel Worlds / Interconnected / Memory Geist
1 group owner
www. parallel - worlds - music. com
www. myspace. com/ parallelworldsmusic
www. myspace. com/ interconnectedmusic
www. myspace. com/ memorygeist
www. DiN. org. uk
www. musicamaximamagneti ca. com
www. vu-us. com
www. shimarecords. co. uk
--- On Sat, 2/13/10, stevebdar <stevebdar@yahoo. com> wrote:
From: stevebdar <stevebdar@yahoo. com>
Subject: 1 Newbie Question: Adding a Plan B M17 to a Doepfer 9U Case
To: Doepfer_a100@ yahoogroups. com
Date: Saturday, February 13, 2010, 6:46 AM
I've been buying modules (always looking) for my new modular set-up which will be housed in a Doepfer a-100lc9 9U case.
My question is about adding a Plan 9 M17 to this case. Will it connect to the bus like a standard Doepfer module or will I need a special ribbon cable and connector
Thanks
Steve B
[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed]