Hi Dieter.

I try again today and use the pre-post and not pos-post and work perfectly...
I dont know what is the difference considering the glide is 0...

--- In Doepfer_a100@yahoogroups.com , <yahoo@...> wrote:
>
> My recommendation is to use the single step to adjust each note of the
> sequence. Move the knob CW until the next semitone beyond the wanted tone is
> generated. Then turn the knob CCW until the semitone below the wanted tone
> is generated. Then turn the knob into the middle of these two positions.
> Then you should be in the "center" of the right tone and no toggling (e.g.
> D/D#) should occur. I know that's a bit long-winded but it's a solution.
>
> Best regards
> Dieter Doepfer
>
> > -----Ursprüngliche Nachricht-----
> > Von: Doepfer_a100@yahoogroups.com
> > [mailto: Doepfer_a100@yahoogroups.com ]Im Auftrag von aletropdj
> > Gesendet: Mittwoch, 14. Dezember 2011 14:57
> > An: Doepfer_a100@yahoogroups.com
> > Betreff: 1 Re: A-156 problem
> >
> >
> > :/
> >
> > So I'll never have a solid sequence...
> > i will try again.
> >
> >
> >
> > --- In Doepfer_a100@yahoogroups.com , <yahoo@> wrote:
> > >
> > > > Hi.
> > > >
> > > > My quantizer is crazy.
> > > > The connection i normally use is:
> > > >
> > > > A155 > A156 > A110/A140
> > > >
> > > > The problem is the pitch. the notes is not always the same.
> > > > If my patern is C,D,C,D; at some time change for C,D#,C#,D...
> > > >
> > > > The gate not always trigger. at some time dont trigge one step.
> > > >
> > > > What is the problem and how i can solve
> > > >
> > > > Thanks
> > >
> > >
> > > I don't think that your A-156 is crazy. You describe a basic
> > "problem" with
> > > each quantizer that is not embedded into the sequencer. A
> > quantizer regrades
> > > incoming voltages and does not "know" anything about a sequence and the
> > > notes/voltages of the sequence (you could use any voltage as
> > input of the
> > > quantizer). If the new incoming voltage is very close to the threshold
> > > between two steps (e.g. D and D#) the output voltage may sometimes
> > > correspond to D and sometimes to D#. This could be avoided only by a
> > > quantizer that "knows" that during the last sequence there was
> > a "D" at the
> > > step in question and that he has to repeat this "D" because
> > there is only a
> > > very small difference between the new voltage and the voltage during the
> > > last run.
> > >
> > > To obtain this feature the quantizer would have to memorize the
> > voltage of
> > > the sequenzer step in question during the last run and compare
> > it to the new
> > > voltage. If the difference is less than e.g. 1/24V (half
> > semitone) the same
> > > output voltage is generated as during the last run. This is
> > possible only of
> > > a "supervisor" is available that memorizes the voltages of all
> > steps during
> > > the last run and compares it to the voltages of the next run.
> > But as A-155
> > > and A-156 are separate modules that's not possible. Only a
> > sequencer with
> > > built-in quantizer (like the Dark Time) could offer such a feature.
> > >
> > > It's a bit difficult to understand but I hope I could explain the
> > > A-155/A-156 behaviour.
> > >
> > > Best wishes
> > > Dieter Doepfer
> > >
> >
> >
> >
> >
> > ------------------------------------
> >
> > Yahoo! Groups Links
> >
> >
> >
>