Hi,

Have you considered building your own case Clicks And Clocks in Berlin sell 4U frames (a 126HP frame is 646mm wide so the  controller will fit easily), if you have basic DIY skills it shouldn't be too difficult.

Hope this helps!

Ross

On Monday, November 14, 2016 12:56 PM, "Diego Ragnini diegora@... [Doepfer_a100]" < Doepfer_a100@yahoogroups.com > wrote:

oh yes, I did believe the ribbon being 500 mm, unfortunately the largest intellijel case is 537.3 mm,
so I might opt to build a handle wooden top for the A-100LC3 to make the case portable, wider enough for hosting the ribbon and containing left and right small cases for the 2 PSU's. After transport the ribbon can be layered on the top of the case or anywhere else. The only issue would be for hand luggage on planes, typically asking to stay within 55cm length.

I thank you a lot for support

Best regards

Il giorno 14/nov/2016, alle ore 11:10, yahoo@... 1 < Doepfer_a100@yahoogroups.com > ha scritto:

> Then it should be no problem. Simply mount the R2M manual to a 1U blind
> panel by means of the four M3 threads at the bottom of the R2M manual
> housing. The lenght of the R2M manual is ~ 600 mm (plus the USB connector).
> If the width of the case is more it should work. I'd recommend to keep the
> housing as it guarantees the mechanical stability required for the pressure
> and position sensors.
>
> Best wishes
> Dieter Doepfer
>
>
>> -----Ursprüngliche Nachricht-----
>> Von: Doepfer_a100@yahoogroups.com [mailto: Doepfer_a100@yahoogroups.com ]
>> Gesendet: Montag, 14. November 2016 10:58
>> An: Doepfer_a100@yahoogroups.com
>> Betreff: Re: 1 R2M Manual Ribbon controller - 1U row
>> installation
>>
>>
>>
>>
>> Thanks, though I imagined a row longer than 84hp, there's some on
>> sale of 90HP, 104HP, 1 row @ 3U + 1 row @ 1U. I do believe that
>> Intellijel makes it. Of course, then it would require some work
>> to manufacture a panel to host the Manual.
>>
>>
>> Best regards, Diego
>>
>>
>>
>> Il giorno 14/nov/2016, alle ore 10:45, yahoo@...
>> 1 < Doepfer_a100@yahoogroups.com > ha scritto:
>>
>>
>>
>> I'm sorry, this will not work because the position sensor is longer than
>> 19". The active area of the position sensor is 500 mm plus the
>> area required
>> for the connector (~ 70mm). That's more than 19" which is about
>> 483 mm. It's
>> not possible to shorten the positions sensor without damaging the
>> sensor (in
>> contrast to the pressure sensor which can be easily shortened).
>>
>> Best wishes
>> Dieter Doepfer
>>
>>> Hello,
>>>
>>> is there anybody who tried to ease installation of the manual
>>> onto a 1U eurorack row
>>>
>>> Thanks
>>
>>
>>
>>
>>
>>
>>
>>
>
>
>
> ------------------------------------
>
> ------------------------------------
>
>
> ------------------------------------
>
> Yahoo Groups Links
>
>
>



------------------------------------

------------------------------------


------------------------------------

Yahoo Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Doepfer_a100/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/Doepfer_a100/join
    (Yahoo! ID required)

<*> To change settings via email:
    Doepfer_a100-digest@yahoogroups.com
    Doepfer_a100-fullfeatured@yahoogroups.com

<*> To unsubscribe from this group, send an email to:
    Doepfer_a100-unsubscribe@yahoogroups.com

<*> Your use of Yahoo Groups is subject to:
    https://info.yahoo.com/legal/us/yahoo/utos/terms/