sorry, that was just meant to go to Peter.
best,
pH
> hi Peter,
> I'm in for at least one... would like two, but just put a deposit on the new EH
> 16 sec delay.... so not sure I can afford two now... too many new toys!
> best,
> phil
>
>
> > Based on interest expressed from your letters (thank you!) and
> > after speaking with Dieter and getting the thumbs up to produce
> > my VCO, it looks I'm going to do just that in a limited quantity.
> >
> > These will be marketed under the company name 'Plan B' and
> > will be in Doepfer height, 90mm wide (45HP), will use the same
> > jacks as Doepfer but with the soft touch knobs used by Analogue
> > Systems. The will run on either +/112 or +/-15 and will use
> > Doepfer's 16 pin dual in line power configuration on the PCBs.
> > For a general idea of what this VCO will look like, go here:
> >
> >
http://www.buzzclick-music.com/Doepfer_rendered2.jpg
> >
> > I'm going to d a maximum of 25 pieces, but will need a minimum
> > of a 10 piece order to go forward with this.
> >
> > Price: $200.00.
> >
> > Payment: 50% down, 50% plus shipping (FOB Los Angeles, CA)
> > on completion prior to shipment. Paypal is preferred, money
> > orders accepted, please no cash or cpersonal checks.
> >
> > Schedule:
> >
> > I am not by any means even close to a large scale manufacturer.
> > I am requesting 50% down so that the components may be
> > purchased and the faceplates and PCBs can be produced. I
> > have about a week's worth of finalization to do on the design to
> > get it to production status. Once this happens and orders are
> > received, I will purchase the raw materials and we can expect 4
> > weeks from that date for delivery of the PCBs and faceplates. I
> > will need approx 1 day per unit for assembly, testing and
> > calibration after that. I apologize for the way I have to handle this,
> > but again - I'm not a large scale manufacturer!
> >
> > These will come with a 1 year warranty for anomalies caused by
> > manufacturing. Damage due to misuse must be billed, but at
> > only a $25 surcharge during the first year (not including parts).
> >
> > I AM NOT TAKING ORDERS YET! I do ask that you contact me
> > offline to determine the demand for this module and if it warrants
> > going into production. During this time I'll be working on the
> > design finalization.
> >
> > You can get me at
peter@...
> >
> > Due to the complexity of this assemnby I will not be able to sell
> > bare PCBs at this time. This VCO incorporates a
> > heat-conductive epoxy encaspulated sub module for
> > temporature stability and both through hole and SMT
> > components - it's a tricky assembly process.
> >
> > So let me know if you're interested and thanks again for
> > expressing interest in this instrument.
> >
> > Features:
> >
> > Controls:
> >
> > Freq
> > Fine Freq
> > Freq VC1 attenuation
> > Freq VC1 attenuation
> > FM level
> > Wave Morph
> > Pulse Width
> >
> > Jacks:
> >
> > Outputs:
> >
> > Sine out
> > Triangle out
> > Saw out
> > PWM out
> > Morph out
> >
> > Inputs:
> >
> > Freq VC 1
> > Freq VC 2
> > FM in
> > 1v/oct in
> > Sync
> > Wave Morph VC
> >
> > Switches:
> >
> > Wave Morph Wave B select
> >
> > General Specs:
> >
> > Frequency range: 5 to 20K hertz
> > Fine Freq range: 20 hz
> > 2 bipolar control voltage inputs (full + and - processing)
> > Expo FM
> > Manual and VC crossfade WaveMmorphing from Sine to either
> > Saw or Square
> > Manual and VC PWM
> > One 1 volt/octave input
> >
> > best,
> >
> > Peter Grenader
> > (now of Plan B!)
> >
> >
> >
> >
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
> >
>
>
>
>
> Yahoo! Groups Links
>
>
>
>
>