Hi,

After more tests, it almost works fine. But there are still things I don't explain.

First, the global parameters are:
B1 = 1
B2 = 16 (tried with 1 too)
B3 = not used
B4 = 1
B5 = 1
B6 = 0
B7 =1
B8 = 0
B9 = 0
B10 = 0
B11 = 0

I've tried with 2 midi interfaces, with just one. The result is the same:
Now, I can play and record the jx-3p but, there are still midi artefacts occuring anytime. It's ok for a few measures and then the seq is pertubed by some midi notes.
There's always a high and a low note, and they never get off unless I use the panic button.

This is what I monitored when the artefact happens:
TIMESTAMP IN PORT STATUS DATA1 DATA2 CHAN NOTE EVENT
00286C77 14 10 9F 00 00 16 C -1 Note Off
00286C77 14 15 9F 00 00 16 C -1 Note Off
00286C79 14 10 9F 20 71 16 G# 1 Note On
00286C79 14 15 9F 20 71 16 G# 1 Note On
00286CF7 14 10 9F 20 00 16 G# 1 Note Off
00286CF7 14 15 9F 20 00 16 G# 1 Note Off
00286CF9 14 10 9F 00 71 16 C -1 Note On
00286CF9 14 15 9F 00 71 16 C -1 Note On

Note: the midi sequence doesn't play these notes.

It happens also when only the midi in is plugged in the 3p ! Very surprising !!

I really don't understand how it could sound like a midi loop with only the midi in connected.

Murray did you sequence the 3p in your tests 1 2
Nobody with the same problem 1 2

Thanks

--- In kiwitechnics@yahoogroups.com , "poiskaill" <poiskaill@...> wrote:
>
> Hello and thanks for your reply !
>
> I've managed to access to the global parameters:
> I put 'goup a / bank b / 8 & 9' on the first position. I think it's the off position cause my sytem works better now.
> I set midi channel in on 1 and the out on 16.
>
> There are still things non ok:
> - the output sends a lot of CC: LSB & MSB, also the PC Brite acc piano (on all the sounds, it send this specific PC).
>
> - Recording midi notes: I can record every type of instruments with one note at the time (piano, bass, pad). I can also record chords with a piano sound, but I can't with a pad: when I release the keys, the notes are still active and then release after. Also, if I play a new chord or notes during this note sustaining, the midi recorder can't see the new notes.
>
> I'll try to make a video of it, will be easier to understand ;)
>
> Also,
> on the website, the last 3p upgrade's update is not downloadable (error 404).
>
> best regards
> F
>
>
>
> --- In kiwitechnics@yahoogroups.com , Kiwitechnics <yahoogroups@> wrote:
> >
> > Assuming you are using v2, try turning off Global Parameters Group
> > A:Bank B:8 & 9. This will switch off the passing of midi from the in to
> > the out ports.
> > Midi Channels are also set in Group A:Bank B:1
> >
> > Sorry the manual is hard to read. It's a little complicated. Print out a
> > A3 colour copy of the Menu Map as that will help you to find your way
> > around.
> >
> > To edit the global parameters you press Shift (tape button), Group A:
> > Bank B: then 1 to 16 depending on the parameter you wish to edit. There
> > is a table of these in the menu map.
> >
> > MH
> >
> > On 6/11/2011 9:57 a.m., poiskaill wrote:
> > >
> > > Hi,
> > >
> > > Since I've installed the 3p ugrade, I don't recognize the use of my
> > > synth, and I feel really lost reading the 3p upgrade's manual.
> > >
> > > The 3p has midi in & out connected (it's also my master keyboard).
> > > I can get it work properly: there's a midi loop I can't get rid of (no
> > > loop before the upgrade).
> > > Also, just with the midi in connected, a single note sent from Cubase
> > > and the 3p takes the notes and keep it alive, no way to stop it.
> > >
> > > I have also the PE wich is working fine thru Cubase. No problem
> > > controlling the 3p on the same channel the notes were send.
> > >
> > > How to go in 'global parameters' to set the midi channels 1 2
> > >
> > > I think It should be a good start ;)
> > >
> > >
> >
>